honest reliablemade by kiwis

Fishing Rod Cork & EVA Grips

 
The most common materials that are used to fashion grips for fishing rods are "High density" brushed EVA foam, and Cork.
Cork is a natural product grown on a tree and EVA (Ethylene Vinyl Acetate) is a man made product which comes in various densities.
 
Shapes and sizes vary according to the rod being built and both materials can be modified by shaping and reaming out to suit the blank you are building your rod on.
 
We can custom build grips by cutting, shaping, sanding and reaming if you have a special requirement. Send us an email with your requirements and we will give you a quote.
 
Brushed Hi Density EVA Foam
 
EVA finished(copy)(copy)
EVA Grips
 

EVA foam handles and grips are in common use in fishing rods today.


Not all EVA is created equal
though, and it is important to know this and go that extra mile and insist on using the "High Density" variety. This is easily shaped, sanded and reamed out using the correct tools and work practices.

This fact is important as, although preformed EVA grips come in many different internal bore sizes, sometimes the bore has to be reamed or sanded to suit the taper of the blank. This becomes evident when using a fast taper blank where the internal measurement of the grip at the base is a few millimetres larger than the internal measurement at the top of the grip.
 
Eva grips can be forced on to blanks with air pressure, but this is not the best way when the grip has to expand more than a millimetre or so. The pressure exerted on the blank can be quite considerable and the epoxy glue spread on the blank to fasten the grip can be wiped off by this pressure, resulting in a weak bond.
   By their very nature, 2 pot epoxy glues are "gap filling" adhesives and perform best when there is an adequate amount available to bond both the surfaces together. If there is not a good bond, the grip can end up twisting on the blank.
 
Lower quality EVA grips which are softer and less resilient tend to be harder to work with and unfortunately they can "move" in your hand when applying pressure while fighting a fish. On heavier rods, they tend to tire out the angler as the fore grip has less resistance to movement under the hand which is applying the most pressure and trying to counteract the effect of winding the reel. As you can imagine, the larger the reel, the more correcting pressure has to be applied. A great way to get blisters!

     
  Most EVA grips come in basic Black, but can come in many different colours even camoflage colours and patterns and imitation Cork sometimes referred to as Korkalon.
 
 
Pre-shaped Cork
 
Cork finished(copy)(copy)(copy)


Cork handles and grips have been floating around since Noah was a boy and for good reason.
 
Most Graphite Fly rods and light spinning rods are suited to this material as it is an excellent material for smaller grips. Cork is light weight, warm to the touch, reasonably easy to shape and ream with the correct tools and work practices.
 
It tends to be a tried and true material which transmits the vibrations from the light blanks to the angler well.
 


thick parallel cork(copy)(copy)


Short parallel grip 35mm OD
full wells cork(copy)
Fly rod grip #1
 
split grips(copy)
 
Cork & EVA split grips


parallel cork(copy)(copy)

 
Long parallel grip 25mm OD
half wells(copy)(copy)


 
Fly rod grip #2
 
Small fighting butt(copy)
Small fighting butt
Large fighting butt2(copy)(copy)
Large fighting butts
 
When working with Cork, tend to be a little slower when sanding or reaming as the material can heat up very quickly when shaped on a high speed lathe. The practice of little steps works well in this case.
 
If you want any more information on Fishing Rod Grips, send us an email.


 
SIGNUP FOR SPECIAL OFFERS, DISCOUNTS & NEWSLETTERS
Email
 
CUSTOMER SERVICE
Contact us
Privacy Policy